Step Tutorial for Bathtub Installation
Step Tutorial for Bathtub Installation
Blog Article
We've discovered this great article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround directly below on the net and thought it made perfect sense to relate it with you in this article.
Installing a bathtub isn't specifically rocket science, yet it does call for strong plumbing, carpentry, and often, tiling skills. Replacing an old bath tub with a new one is additionally a moderately tough project. If the old tub is readily obtainable, the project can relocate easily; if you need to open up a wall surface to eliminate the old bathtub and place the brand-new bath tub, the task is much harder. In either case, the job is within a residence handyman's skills, although you will certainly require a helper to vacate the old bathtub as well as set in the new one. Make sure you have qualified on your own for the job and also fit attempting it. Instead of employing a specialist to take over a halfway-completed job, it is better to consider utilizing one prior to you begin. Chances are you might require a specialist plumber to make tube connections.
This write-up will certainly aid you set up a new bath tub in your shower room if you have actually already gotten a new bathtub and also do not need to transform the plan of your previous water system pipelines.
Your devices as well as product checklist need to comprise the following:
Preparing for the Setup
To start with, the supporting structure provided with the bath ought to be fitted (if needed) according to the producer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to make certain that if the faucet features a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps unit to stop strain on the bath tub.
Fit the adaptable tap connectors to the bottom of both taps making use of 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you utilize every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its last placement.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your setup, after that the first thing you must do is detach the water system. After doing so, activate the faucets to drain any kind of water continuing to be in the system. The process of removing the existing taps can be rather troublesome because of the restricted access that is frequently the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the faucets. Have a fabric all set for the remaining water that will certainly originate from the pipelines. Once the supply pipelines have been gotten rid of, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any kind of old sealing substance.
Prior to proceeding to fit the brand-new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Mounting the Tub
Utilizing the two wooden boards under its feet, position the bathtub in the called for placement. The wood boards are useful in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four little points.
The following goal is to ensure that the tub is leveled all round. This can be achieved by examining the spirit level and changing the feet on the tub till the spirit level checks out degree.
To set up taps, fit the bottom of the outermost flexible tap connector to the suitable supply pipe by making a compression join; then do the same for the other tap.
Switch on the water system as well as check all joints as well as new pipework for leaks and tighten them if required. Load the bath tub as well as also examine the overflow electrical outlet as well as the typical outlet for leakages.
Finally, take care of the bath paneling as defined in the maker's user's manual. Tiling and also sealing around the bath tub should wait up until the bathtub has actually been made use of at the very least once as this will certainly resolve it right into its final setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the faucet as well as the other end provides a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will require minimizing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the tap in the mounting hole in the bath/basin ensuring that the washing machines are in location in between the tap as well as the sink. Safeguard the tap in position with the supplier supplied backnut. When the tap is safely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular tap connectors. The previous kind needs to be connected to the tap finishes initially, tightening just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bathroom satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to fracture a rigid seal, creating the water to pass through the wall in between the bathroom and the tiling, leading to complications with wetness as well as possible leakages to the ceiling below.
You can choose from a range of coloured sealers to blend in your components and also fittings. They are sold in tubes and also cartridges, as well as are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of soaked newspaper or soft rope. Keep in mind to always fill the tub with water prior to securing, to allow for the motion experienced when the tub remains in usage. The sealer can split fairly early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also quickly offered on the marketplace. It is advisable to fit the ceramic tiles using waterproof or waterproof sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I discovered that blog entry about A Step-by-Step Guide to Installing a Bathtub while browsing on the internet. Sharing is good. You just don't know, you might be doing someone a favor. Thanks a lot for your time. Don't hesitate to pay a visit to our blog back soon.
Request Service Report this page